Product overview
Separate solar panel and LED fixture
The solar panel and LED lamp are installed separately, allowing the panel position to be adjusted according to site conditions and sunlight exposure.
Solar power and battery storage
The system uses a solar panel to generate electricity and a battery to store energy for nighttime lighting.
Available system configurations
The 80W separate solar street light configuration listed below includes a 180W monocrystalline solar panel and a 25.6V 45Ah LiFePO4 battery. Other configurations should be selected according to the project requirements and confirmed technical specifications.
-
All In Two Solar Street Light8m Poleread more
60W Solar LED Light
180w solar panel
Lithium Battery Box(It contains Lithium Battery & Controller)
Split Solar Street Light .
High efficiency, energy saving,... -
Separate Solar Street Light80W Solar Street Light.read more
Integrated with 180W monocrystalline panel,
25.6V 45Ah LiFePO4 battery and smart PWM controller.
IP66 waterproof,
low-light charging,... -
Split Solar Street Light 80WLED Lamp: Split Solar Street Light 120Wread more
Solar Panel: 200W solar panel+120W Octagonal panel
Solar Energy Storage: LiFe PO4 Lithium Battery 25.6V 45Ah it can be customized
All In... -
All In 2 Solar Street LightAll In 2 Solar Street Light 50Wread more
Highly Cost Effective, High Efficiency, and long Life
Cycle 50W LED street Light
High Efficiency Solar Panel Solar Panel 36V 250W*2PCS
High... -
Off Grid Solar Street LightRated Power: 90Wread more
•Light Source Type: High-power COB LED chip (high color rendering index)
•Luminous Flux: ≥9000LM
•Color Temperature: 4000K-7000K (customizable)
Off Grid... -
Separated solar street lightSeparated solar street lightread more
LED Lamp 100W Solar Street Light
Solar Panel 200W solar panel
Solar Energy Storage LiFe PO4 Lithium Battery 25.6V 75Ah
high-performance...
Key specifications
|
Parameter |
80W separate solar street light |
|
LED rated power |
80W |
|
Solar panel power |
180W |
|
Solar panel type |
Monocrystalline silicon |
|
Battery type |
LiFePO4 |
|
Battery voltage |
25.6V |
|
Battery capacity |
45Ah |
|
Controller |
Smart PWM controller |
|
Protection rating |
IP66, as listed for this configuration |
|
Charging performance |
Low-light charging, as described for this configuration |
|
Lamp arm diameter |
Φ60–89 mm |
|
Lighting control |
Light control and intelligent lighting modes |
Additional technical details to confirm
Luminous flux, correlated color temperature (CCT), operating temperature, lighting duration, backup days, recommended installation height, warranty terms, and other project-specific requirements should be confirmed against the final product datasheet before ordering.
Configuration options
LED power
Select the rated LED power according to road width, installation height, required illumination, and project design.
Solar panel
Solar panel power should be matched to the lighting load, local solar conditions, and required charging performance.
Battery and controller
Battery capacity and controller configuration should be selected according to nightly operating hours, expected weather conditions, and backup requirements.
Mounting and lighting control
Confirm the lamp arm diameter, mounting arrangement, lighting schedule, and control functions before installation.

Roads and rural areas
Suitable for road lighting projects where access to grid electricity is limited or where a standalone solar lighting system is preferred.
Parks and residential areas
Can be considered for outdoor lighting projects, subject to the required illumination level and site layout.
Industrial areas and parking lots
Suitable for evaluating in outdoor areas where lighting positions, operating hours, and installation conditions can be specified.
Remote locations
A separate solar configuration can be considered for sites where connecting to the electrical grid is difficult. System sizing should be based on local sunlight conditions and required lighting performance.
Installation and operation
Site assessment
Confirm the installation location, sunlight exposure, pole height, road or area layout, and local weather conditions before selecting the system.
Mounting and electrical connections
Check the pole and lamp arm dimensions, secure the solar panel and LED fixture, and complete electrical connections according to the approved installation instructions.
Commissioning
Verify charging, battery operation, lighting control, and the programmed lighting schedule before the system enters service.
Maintenance
Inspect the solar panel, mounting hardware, electrical connections, and lighting performance periodically. Keep the panel surface clean and follow the product maintenance instructions.
Customization and supply
Project-based configuration
Provide the required LED power, solar panel and battery specifications, installation height, lighting schedule, and local weather conditions to support configuration selection.
Component confirmation
Confirm the solar panel, battery, controller, LED fixture, mounting dimensions, and protection rating against the final technical datasheet.
Manufacturing and quality control
Product specifications, inspection requirements, and quality documentation should be confirmed with the supplier before production.
Bulk orders and OEM requirements
For distributor, contractor, and project orders, specify the required configuration, order quantity, packaging requirements, and any agreed customization details.
FAQ

Request a quotation
To help determine a suitable split solar street light configuration, please provide the following project details.
Application and installation location
Required quantity
LED power or lighting requirements
Pole height and lamp arm dimensions
Expected lighting hours per night
Required backup period for cloudy or rainy weather
Preferred solar panel, battery, or controller configuration
Any project-specific technical or customization requirements
The final configuration and technical specifications should be confirmed before production.
Yantai Xutai New Energy Technology Co., Ltd. is one of the most professional split solar street light manufacturers and suppliers in China. With a professional production team, we are able to meet the needs of the majority of our customers. Please rest assured to buy premium split solar street light made in China here from our factory.
All In 2 Solar Street Light, Off Grid Solar Street Light, Separated solar street light-
Self-maintaining solar street lightModel: XT1958SELD150-SCread more
Power: 150W
Solar Panel: Monocrystalline Silicon of 36V/180W
Battery: LiFe... -
Smart all in one solar street lightModel: XT1968SELD200-D5read more
Power: 200W
Solar Panel: Topcon 255W
Battery: LiFe PO4 Lithium Battery... -
All In Two Solar Street Light8m Poleread more
60W Solar LED Light
180w solar panel
Lithium Battery Box(It contains Lithium Battery &... -
Solar Street Light PoleApplication: Highways, city roads, parking, industrial area, residential communities, village roads, and all kinds...read more



